|
|
|
|
|
|
|
|
¹®ÀÇ:031-468-8560 FAX:031-468-2067 HP:010-3203-8293 |
E-mail ¹®ÀÇ |
|
|
|
|
|
|
|
| Áú¹®°ú ´ë´ä | |
|
| Matrix ¹èÅ͸® ¸®¼Â¹æ¹ý |
| |
2007/05/29 (16:11) |
|
ÀÛ¼ºÀÚ : Á¤¿î¼·
|
Á¶È¸¼ö : 2717 |
|
This document outlines the steps to take when trying to reset the SmartCell XR communications module. The SmartCell XR onboard microprocessor will turn itself off (sleep mode) after approximately 30 seconds if the communications cable is removed from the "BATT COMM OUT" jack. This is to prevent the board from discharging the batteries, down to dangerous levels, during shipping/storage. To successfully reset the communications module you need to wait for the board to go to sleep.
This board will report to the UPS the state of charge of the batteries (# Float Batt) or if the batteries need to be replaced (# Bad Batt). If the "Replace Battery" indicator is either "ON" (without cause) or blinking, please follow the procedure outlined below:
1. SmartCell XR µÞÂÊ¿¡ ÀÖ´Â RJ-11 Àüȼ±ÀèÀ» »«´Ù.(UPS out ÂÊ)
2. 30ÃÊ(60ÃÊ)ÀÌ»ó ±â´Ù¸®¸é ¹èÅ͸® ÆÑÀÇ LED°¡ ²¨Áø´Ù.
3. º¼ÆæÀ̳ª '¤Ó'ÀÚÇü À̾¥½Ã°Ô·Î ¹èÅ͸®ÆÑÀÇ Åë½ÅÀè »çÀÌ¿¡ ±¸¸Û¿¡ ¸®¼Â¹öÆ°À» ±æ°Ô ´©¸¥´Ù.
4. ´©¸£°í ÀÖ´Â µ¿¾È ¹èÅ͸® Åë½Å ÄÉÀ̺íÀ» UPSº»Ã¼¿¡ ²Å´Â´Ù.
5. ¸®¼Â¹öÆ°À» ¶¾´Ù.
a. ¹èÅ͸®ÆÑ Àü¸é¿¡ LED°¡ ±ô¹Ú°Å¸°´Ù.
b. LED°¡ ±ô¹Ú°Å¸®¸é ¾Æ·¡ ´Ü°è¸¦ ½ÇÇàÇÑ´Ù.
6. ¹èÅ͸®ÆÑ¿¡ Åë½ÅÄÉÀ̺íÀ» º»Ã¼¿Í ´Ù½Ã ºÐ¸®ÇÑ´Ù.
7. 60ÃÊ Á¤µµ ±â´Ù¸®¸é LED°¡ ²¨Áø´Ù.
8. ¹èÅ͸®ÆÑ°ú º»Ã¼ Åë½ÅÄÉÀ̺íÀ» ¿¬°áÇÑ´Ù. À̶§ ¸®¼Â¹öÆ°Àº ´©¸£Áö ¾Ê´Â´Ù.
9. ¹èÅ͸® ±³Ã¼°¡ ¿Ï·á µÇ¾ú½¿. ¸¸¾à ±×·¡µµ Replace Battery ¸Þ¼¼Áö°¡ ³ªÅ¸³ª¸é À§ÀÇ ¹æ¹ýÀ» ´Ù½Ã
½ÇÇàÇÑ´Ù.
|
|
|
|
|